set of remote control, united, 3 pcs
& nbsp; SRC = "/userfiles/C306DA56-2EB3-4785-8435-B636B2AF0691/Image/logo_unite.jpg" style = "height: 68px; width: 229px"/>
& nbsp;
- used for remote starting/stopping electrical and lamps. ) + 1 remote control.
- The range is maximum 40 m (without obstacles). 50/60 Hz
- Nominal current: 4.35 A
- Maximum power: 1000 W
- Frequency: 433.92 MHz
- Remote control: 1 x Battery CR2032
- Color: white
- Material: PVC
- Dimensions: 18 x 6 x 16 cm
- Weight: 381 g
& nbsp; The devices cannot be attached to the remote control sockets:
-
-
- monitors, TVs
- appliances whose values cannot be transmitted to the switch
-
- engine & nbsp; By condensation, eg refrigerator
- ironing iron and other devices that do not have overheating
-
- The sockets are not used In wet spaces (bathroom, cellar, etc ...)
-
- the remote control socket will only be introduced to protection with protection (grounding), (230V-/50Hz)
-
- the sockets will not be mounted in each other. (thickness of the walls) as well as for reasons of electric/electomagnetic interference (wifi devices, mobile phones, electric cables, monitors, TVs, etc.)
& nbsp; >
Setting of the sockets:
-
-
- Put the battery in the remote control
- < Span> The remote control can be scheduled in such a way that each key (A, B, C) can be subordinated to an transmitter that you can start, stop, or key to start or stop all the transmitters.
the setting of the transmitters will be done in a row, not all at once (except the D key).
Insert one of the transmitters into a protective socket. will light LED & RSQUO; the intermittent red color for approx. 30 sec. will be pressed shortly the desired key (eg a) from the left/on & nbsp; of the remote control. A & ldquo will be heard; click & rdquo; And the LED remains lit. Press the right/off key, (eg a) to extinguish the device. Now the socket is scheduled according to the chosen key (eg) on the remote control. . (B, c) & nbsp; >
- The D key is for the common setting of the three transmitters.
- To set all the emitters to start at the same time the following will be performed:
If you already have the emitters entered in & nbsp; The sockets must be removed for 5 sec. and introduced again. 30 sec. will be pressing the D key from the left/on the remote control. A & ldquo will be heard; click & rdquo; And the LEDs remain lit. Press the right/off key, D to extinguish the devices. & nbsp;
at this time the sockets are set both individually (a, b, c) and common (D).
& nbsp; In another way, the transmitters or you have wrongly scheduled you can reset the transmitters as follows:
if you already have the emitters entered in & nbsp; Prizes these must be removed for 5 sec. and introduced again. 30 sec. press the key on the right/off, (the one that corresponds already chosen, eg A, D) & nbsp; LED & RSQUO; UL intermittently (quickly, ca. 2 sec). At this moment the settings were deleted and to set them again follow the steps from La & ldquo; Setting of the & rdquo sockets; & nbsp;
attention !!! -
- if interrupted & nbsp; The current or you have removed the transmitter from the outlet, it is important that for approx. 30 sec (as long as LED & RSQUO; the ul is flashing) not to order on the remote control, so you risk disturbing the settings chosen above. After the LED goes out, you can use the remote control according to the chosen settings.
- do not introduce in the transmitters whose power exceeds 1000W. The appliances introduced into the transmitters are started (if applicable). their.
- to avoid certain dysfunctions, it is advisable that the emitters are located at a distance of 1 meter between them.